Wall Putty

Wall Putty

Non- CURING

This is premium non-curing wall putty specially developed as a finish coat to cover unevenness and pinholes in plastered surfaces and to make the walls/ceilings ready for painting. It resists efflorescence in plastered walls. It is also highly water resistant. As it is white, it can be treated as a base coat for painting.

 

FEATURES & BENEFITS

  • Efflorescence resistant
  • Water resistant
  • Excellent bonding to the base plaster/concrete
  • Scratch resistant
  • UV resistant
  • Reduction in cracking
  • Can be used on new as well as old walls / ceilings
  • Excellent workability
  • Ease of use at site
  • Suitable for interiors as well as exteriors
  • Consistent work quality
  • Excellent, super smooth, super white finish
  • Reduced paint consumption
  • Saves time
  • Cost effective

TECHNICAL ​ INFORMATION

  • PICK TABLE FROM WORD DOCUMENT
  • Pot life    60 minutes
  • PH  Alkaline
  • Coverage  15-20 sq ft/ kg, Depending On finish of the wall.
  • Recommended mixing ratio 300-400ml water/kg of wall putty
  • Package : 20 Kg & 210 Kg

AREA OF APPLICATION

PLASTO MIX  used buildings will be more durable and the potential savings on long term maintenance expenses will be substantial.

INSTRUCTIONS: PRECAUTION / STORAGE

HOW TO APPLY: SURFACE PREPARATION

Clean loose particles, dirt, grease and traces of foreign material from the surface, if necessary, by using sand paper or by chipping.

For loose plaster areas, remove the defective material and re-plaster the area.

For ceiling / walls, which are not even re-plaster it with rich plaster to make them even.

Fill up any cracks in base plaster by using YANKONIZE CRACK FILL.

MIXING

Take 10-12 liters of clean water per 40kg bag in a clean bucket. Add the required quantity of YANKONIZE WALL PUTTY. Adjust the water to the amount of plaster used at a time. Add further water as required.

Stir continuously by using an electric mixer or by hand to obtain a homogeneous lump-free paste.

Allow the resultant paste to stand for about for about 10 minutes for the additives to dissolve.

Re-mix again for about 2 minutes.

Use the mix within 60 minutes. 

APPLICATION:

Dampen the surface to be plastered with clean water. Allow excess water to drain off.

Using a steel trowel / blade, apply, apply the above mix to a thickness of about 1 mm. Level and smoothen the surface. Wet sponge the coat gently after it dries.

Apply the second coat after the first coat has fully dries and set. Wet sponge the final coat gently after it dries.

The thickness of each coat should not exceed 1mm and total plaster thickness should not exceed 1.5mm.

Smoothen with a steel trowel. Sand paper if so desired, with 600no. Sand paper.

After the final coat has dried and set, wipe it with a wet sponge.

PRODUCT LIMITATIONS:

As efflorescence is caused by various reasons and in various degrees, although this product resists efflorescence, it may not be able to guarantee total eradication of efflorescence.

ENVIRONMENT:

WALL PUTTY contains only eco-friendly raw materials and polymers and is harmless to ecology as well as the user.

PRECAUTIONS:

WALL PUTTY contains only eco-friendly fillers and additives. However, being white cement based, it is alkaline and hence it is advisable to avoid direct eye and skin contact with this, incase of eye contact, flush with clean water at least for 15 minutes and seek medical help.

PACKAGING & STORAGE:

WALL PUTTY is supplied in 30kg bags and has a shelf life of 6 months if stored in a cool and dry location.

As temperature, humidity. Water addition and parameters vary from site to site, the above information shouldbe treated as a general guideline.

Wall Putty
Scroll to top